Doing commercial sidewalk snow removal the right way

When you're clearing snow off your sidewalks, there are a few things you need to keep in mind. First, make sure that you have plenty of space between your vehicle and the curb so that you don't hit any pedestrians or other vehicles as you're trying to push about two tons of snow out of the way. Second, be careful if you try to put salt on the sidewalk because it can damage vegetation and pavements. Finally, make sure that your equipment is in good working order before clearing snow from commercial sidewalks.

The first course of action in clearing snow from sidewalks is to assess the situation. In many cases, this means checking for traffic on the street and figuring out how long it will take for the snow to melt before it becomes a hazard. If you're dealing with a large amount of snow, or if the sidewalk is narrow and hard to reach, you may need to remove it all at once.

If you have time and a few people on hand, your best bet is to start by clearing an area about 50 feet wide along the length of the sidewalk. This will allow you to easily reach each side of the walkway and avoid having to shovel entire sections of your sidewalk at once.

Once you've cleared an area along each side of your walkway, turn your focus back toward the center where most of the snow was removed. Use shovels or leaf blowers to pick up any remaining pieces that aren't stuck under parked cars or other obstacles.

Next, assess how much work remains once all the large pieces have been cleared away. In most cases, this means scraping off any remaining ice and packed-down snow (and then removing all foreign objects such as leaves or twigs). Don't forget about holes in which water has pooled as well!

How to clear snow from sidewalks?

Sidewalks loaded with snow are a danger for everyone. Appleton snow removal mainly focuses on sidewalk and entryway ice damage as it gets pretty chilly here in the winter months. The same is true for other cities as well. For example, St Paul plowing services generally specialize in clearing sidewalks, roads, and parking lots. 

Snow falls in the winter, and it's time to clear sidewalks. Here's how you should do it:

  1. Call the city or local government.
  2. Don't use a snowblower or other commercial equipment without getting a permit first. Using a broom instead of a snowblower is also a good option.
  3. Avoid using a push broom, as they can damage the pavement and make it more difficult to plow in the future.
  4. Use a snow shovel to remove snow from sidewalk edges and inside walkways, rather than just blowing out the snow directly onto sidewalks with your hands (which can damage the pavement).
  5. You can also make use of ice melt on the sidewalks instead of salt.
  6. Always keep your sidewalks clear of leaves and debris as they can aggravate the problem and lead to more expansive ice damage from the winter snow.

How to salt sidewalks in winter?

Salt is a great way to de-ice your sidewalks, but you need to do it correctly.

Salt will not melt ice and snow. Salt will not make the ice and snow softer. Salt can actually increase traction on wet ice and slippery surfaces, so you should use this option only if you have a large amount of snow on your sidewalk.

Here are some safety tips for clearing snow from sidewalks in winter:

Use a shovel or rake to clear any loose snow from the sidewalk before salting it. This will prevent the salt from collecting in small piles or clumps, which could then become icy hazards when wet by rain or melted snow later on.

If you're using salt, start with one-quarter cup of salt per quart (or liter) of water (4 tablespoons per gallon). This can be adjusted up or down depending on how much water is available at your site, but don't try to extend the effectiveness with more than half a cup per quart (2 tablespoons per gallon).

A good rule of thumb is to put down two inches (5 cm) of salt over each inch (2 cm) of sidewalk width and spread it out evenly over all surfaces before salting them with your shovel or rake.

There are a couple of ways that you can make your own salt brine at home:

  1. Salt and water solution: Mix two cups of salt with one gallon of water in a large container and leave overnight. This will yield approximately 3 gallons of salt brine. Note: Do not use any chemicals such as bleach or ammonia in this solution because they can contaminate the water supply if spilled on a sidewalk or driveway during cleaning operations.
  2. Sodium chloride (table salt): Mix one pound of table salt with eight cups of warm water in a large container and let sit overnight before using on a driveway or sidewalk where melting snow will occur (do not add any chemicals). Use a non-corrosive shovel when mixing and spreading the solution onto surfaces (do not use plastic gloves). Avoid contact with skin, eyes, and clothing when working with this solution.

In conclusion

Salting your sidewalks in winter can be the #1 priority for you, but you should also look at other alternatives. Also, you should make sure that the process is as safe as possible. Hiring a reliable commercial snow management service is our recommendation.

Earth Development is one of the best services in the US Midwest offering safe and trustworthy service to companies in winter.

More to Read: